Links
Infiniti G37 Links
Sites of Interest
Recent Discussions
- Re: Weird electric issues....IPDM or BCM?
- Re: Cooling fans stop working when car warms up
- Re: Cooling fans stop working when car warms up
- Re: 2008 Infiniti EX35 - Stiff Steering Continues after Replacing Many Parts
- Re: 2008 Infiniti EX35 - Stiff Steering Continues after Replacing Many Parts
- Re: 2008 Infiniti EX35 - Stiff Steering Continues after Replacing Many Parts
- Re: 2008 Infiniti EX35 - Stiff Steering Continues after Replacing Many Parts
- 2008 Infiniti EX35 - Stiff Steering Continues after Replacing Many Parts
- Re: Weird electric issues....IPDM or BCM?
- Re: Weird electric issues....IPDM or BCM?
- G35 and G37 Engine, Drivetrain & Tuning • Re: Service Manuals
- G35 and G37 Engine, Drivetrain & Tuning • Re: Hello, I’m having issues with my infinti g35 sedan 2008 code U1000
- G35 and G37 Engine, Drivetrain & Tuning • Hello, I’m having issues with my infinti g35 sedan 2008 code U1000
- G35 and G37 Engine, Drivetrain & Tuning • Is this a failing water pump? Or something else?
- G35 and G37 Engine, Drivetrain & Tuning • How much of a reliability decrease when power tuning?
- G35 and G37 Engine, Drivetrain & Tuning • Re: 2011 G25 Accessory Belt Tensioner and/or Pullies
- G35 and G37 Engine, Drivetrain & Tuning • Re: 2011 G25 Accessory Belt Tensioner and/or Pullies
- G35 and G37 Engine, Drivetrain & Tuning • 2011 G25 Accessory Belt Tensioner and/or Pullies
- G35 and G37 Engine, Drivetrain & Tuning • Re: 2014 q40 U1000 and U1001 traction light
- G35 and G37 Engine, Drivetrain & Tuning • Re: Stiff racing clutch, change MC bore?
Of Interest
Wallpapers
Paddle Shifter Installation for Infiniti G37's
|
|||
|
Tools needed: phillips screwdriver, small flat head screwdriver, ratchet w/10mm socket, and patience |
|||
;) |
Step 1. Remove Steering Column Cover Start by turning steering wheel 90* to right from center position. Remove tab covering screw with small flat tip screw driver and then remove screw with phillips screw driver | ||
;) |
Step 2. position steering wheel to the left from center 90* and remove tab and screw using same process in step one. | ||
;) |
Step 3: Remove the small trim piece underneath steering column by gently pulling down and towards front of vehicle | ||
;)
;) |
Step 4: Remove the screws from underneath cover in step 3 and remove bracket. Put aside for reinstallation | ||
;) |
Step 5: Remove the final screw from underneath steering colum bottom cover as shown | ||
;) |
Step 6: Pull the top half of the steering column cover up but don't completely remove. Piece will be used again. | ||
;)
;) |
Step 7: Turn steering wheel from center 180* left or right and pull bottom steering cover down from section closest to steering wheel. This will require a little effort. Then slowly remove the bottom section so you can access the electronic tilt fucntion plug. | ||
;) |
Step 8. Unplug harness for tilt function | ||
;)
;) |
Step 9. There are small push tabs that hold the tilt switch in place, activate those tabs and remove switch and put to the side for reinstallation | ||
;)
;) |
Step 10. Time to reveal the harness plugs for paddle shifter | ||
;)
;)
;) |
Step 11. Install paddle shifter on each side using (1) 6mm nut (1) 6mmx10mm bolt (not supplied)
|
||
;)
;) |
Step 12. Install new steering wheel cover pieces beginning with bottom section, **reuse top section from step 6**. You will also need (1) 12mm trim screw similar to the (3) you removed when taking off the old covers. The (1) screw that was removed from bottom cover can be utilized. If you don't have another one lying around, the pieces will stand intact without. Remember to turn steering wheel 180* left or right from center to begin installing bottom cover. | ||
;)
;) |
Step 13. Install left side cover, be sure to insert the tilt switch and plug harness in. Also be sure to position the tilt switch in the right configuration so the functions move the steering wheel the direction you move the switch. | ||
;) |
Step 14. Install right side cover | ||
;)
;)
;) |
Step 15. NOw position the top half so the (2) trim screws you removed in steps 1 & 2 can be put back into place. | ||
|
|
Step 16. Replace the bracket and trim piece that was removed from step 3 & 4. | ||
;) |
Step 17. Enjoy your new paddle shifters!! *Graphite paddles in Stone interior** | ||
Disclaimer: The author will not be held responsible nor held liable for any damages due to these instructions. Anyone following these directions are doing so at their own risk. This Documentation may not be distributed without the authors consent. |
|||
